Mounting Dream Full Motion TV Wall Mount for Most 42-90 Inch TVs, Heavy Duty Wall Mount TV Bracket with 6 Strong Articulating Arms, Max VESA 600x400mm, Up to 132LBS, Fits 16/18/24” Wood Studs, MD2298

A well-thought-out product!!!
I have to say, this was one of the most well-thought-out products I’ve ever purchased. The item arrived well packaged in a sturdy box (inside another Amazon box) with everything well laid out inside. All of the fasteners were individually packaged so there’s no fishing around for the right part. For the record, I used this to mount a 65″ TV that weighs about 50 lbs. It is definitely sturdy and can hold much more.Additional tools you will need: Tape measure, stud-finder, drill w/drill and screwdriver bits, wrench & socket set (SAE).Mounting on the wall was a breeze. My advice to other buyers that you will need to locate the wall studs accurately and you will need drill the pilot holes as close to the center of the studs as possible – particularly if you’re mounting a heavy TV. There’s just no getting around that. Use the “stud-finder” to mark the edges of the studs, then use those marks to determine the mid-point. Make a couple of passes to be absolutely sure. Included in the package is a peal-and-stick cardboard template and two bubble levels. Don’t bother with the one that you’re supposed to stick on the template, just use the big plastic one. You’re going to want to do some measuring here to make sure you place the mount exactly where you want it. I was lucky that the center of the TV was almost dead-center between two studs. You’ll also want to measure the height of the mount by test-fitting the part that goes on the TV and doing a little figuring on how much to move the mount up or down so that the TV is where you want it.Once you’ve drilled the holes, screw the bracket to the wall and use a wrench to snug the screws tight. Don’t over-tighten or you’ll strip out the holes. Make sure you put the mount right side up (Yes, I made this mistake). Next, attach the brackets to the TV. The kit comes with an assortment of screws, washers and bushings to accommodate any TV. Each TV is different and you’re just going to have to use common sense. Don’t over-tighten these screws either, but the brackets need to be snug.Before hanging the TV on the wall mount, ensure that the side-to-side and front-to-back tilt adjustment screws are tight and relatively level. You can adjust them later to get them perfect, but you should have them close to where they need to be now and tightened down so the mount doesn’t move when you’re trying to hang the TV on it. Have someone help you lift the TV onto the wall mount. It just hangs on there (at first), but it’s much easier if you have someone to help guide it into place. Attach the locking brackets to the bottom of the TV brackets and you’re done!!!Operation of the mount is very smooth, though it takes just a little bit more effort than I’d like. I attribute that to the fact that it’s brand new and I’m certain a few drops of oil strategically placed will resolve that. BY NO MEANS would I suggest getting a different mount based on that purely-subjective opinion. This mount is perfect for a big TV. It’s a little pricier than most, but worth every penny.

I love this mount! – UPDATE
Update 4/30/21. Original purchase 2/19/19.I needed new parts to accommodate a new TV using the same mount. But I didn’t keep the extra parts that came with the mount, so, I called Dream Mount for help. They are sending me what I need (screws and spacers) free of charge. Now THAT’S service.From opening the package to finished install, this piece of equipment was truly a “Dream” to work with. Very high-quality piece of gear. Very easy to install and it feels solid as a rock after installation.I had to build a frame structure in an opening for a recessed TV. That was the hard part. Once the studs were in place, the rest was very easy after I figured out how high to drill the holes in the studs to get the new 55″ Samsung mounted at the right height on the studs.The mount comes with a tiny level for the template and a 6-inch level for checking your work as you go. It also comes with many TV mounting components of different sizes so you can mount any TV. Well packaged and marked. The user manual was also well done and easy to follow.I put the back brackets on the TV using one long spacer for each top hole and one medium spacer for each bottom hole to account for the curve of the rear of the TV. I used the longer, thicker bolts.I then drilled 4 holes with a 7/32″ drill bit, two in each stud where indicated by the template. I could not use the little level for the template because with open studs, the template didn’t lay completely flat. But I used a 2.5′ level of my own to check the levelness of the template on the studs and knew how high to drill the holes by measuring from the bottom of the TV to the bottom mounting bar for the mount.It was a little difficult to put the first bolt into the studs because I had to hold the 22+ lb. mount in one hand while getting the bolt started with the other hand. I’m 72 and not as strong as I used to be. But once I got one bolt in, the rest was easy, using a ratchet to drive the bolts.I had to get help lifting the TV onto the mount. It was just too big and bulky to do myself. But once hung on the mount bars, it was simple to put the hold clamps on the bottom of each side and then adjust the TV for leveling, which in my case, I just used the TV frame and pushed it until it was level. It stayed there and is very solid.I also pulled the TV out to the maximum extension of the mount and turned it so I could see the TV from another room, the kitchen. Very cool to be able to do that, so I can watch TV now while I cook. When I was done checking that, I just pushed the TV back into place, very easily, for watching in the family room.I love this mount. It is very well made and solid. I will be needing another one for our master bedroom soon and I will absolutely buy another one of the exact same model for that job, which will be a flush mount on our bedroom wall near one corner high on the wall. More complicated job because I’ll have to install an electrical and cable outlet up behind the TV so no wires are hanging out. But I know this mount will be perfect for the job.

A estrutura dos suportes apresentam muita resistência e é bem acabado. Usei para uma TV de 50″ e uma de 43″.No kit vêm vários acessórios que são muito úteis na montagem.

Es casi perfecta, la instalé con una pantalla de 43″ y quedó muy bien, justo como me la imaginaba, cumple con todo lo que promete.La instalación es muy sencilla, incluye su propio nivel miniatura, cinchos de velcro para cables y tornillería, una vez instalada se puede ajustar en caso de que haya tenido una inclinación al momento de meter las pijas. El único detalle que le podría dar es que no incluye los taquetes para concreto y por lo menos en mi ciudad no pude conseguir taquetes de la medida de las pijas que venían incluidas [⅜ in x 55 mm(2¼ in)], así que tuve que comprar otras pijas más pequeñas con sus respectivos taquetes y arandelas.Sin duda la recomiendo y la volvería a comprar.